Image Scanner Canon CanoScan 4507B002 3d models

DOUBLE FLYING CLAMP side_hexNut.stl -- 50% side_noHexNut.stl --50% 2x middle_doubleClamp.stl --50% shaft_doubleClamp --90% lever.stl --90% stopper.stl --90% washer.stl --90% guide.stl -- 50% 1/4 hex bolt 1.5 inch 1/4 lock nut 3/16 bolt 1 inch 8x...

(In 3ds Max, the Meshsmooth Function Can Be Used to Increase Mesh Resolution If Necessary) * All Colors Can Be Easily Modified * Model Is Fully Textured with All Materials Applied * All Textures and Materials Are Included and Mapped in Every Format *...

... rest of the body.<br/>You could also tap the support lightly with a small hammer while rotating the knob. The support should break off after a series of very light taps. Take your time and make a series of light hits rather than a few heavy hits.

I cannot take responsibility for any injury when using this maze or its associated parts. Setting Up Add a few treats into the treat container and tightly plug the end with some tissue or shredded paper. This will ensure the treats do not spill out...

Cinema 4D and Vray materials are used throughout this project, with preview images rendered using VrayforC4D. A total of 15 camera setups have been included to provide flexibility during rendering. Light setups are also available exclusively in...

This may result in less audible clicks to ratchet but the lid tension will still work (I will look at this further for the next version). 4.The Clasps will require support and a raft to be printed on their side to maximise strength. 5.The ratchet...

Update V3: I've found a small geometry problem in the eye holder as well as an issue with the thin ring around the eye/cat image being too thin to print nicely. I've made changes to the inserts accordingly. If this print is too tall, please use the...

[](https://www.buymeacoffee.com/csharper) Update 15: added separate lid, and gold, faith, low and high resources box. Update 14: update made to the spacer. All recesses are about .5mm larger in width and length. This way the boxes are easier to...

The entire tool can be printed with 40-50% infill for simple production, or the tool can be printed at much lower (20%) infill for the majority of the tool and only the area that will be subjected to impact can be reinforced with a wedge of 50%...

... on 1sPiRe's work but rebuilt the CAD. I also made the addition of my own fan duct. In the image below you will see I used a cable chain and a laser cut acrylic plate to mount it for wire management. ...This is an area of active work for myself.

Users are free to adjust the body color independently from the images used in pre-view renders, ensuring versatility across a range of visualization styles. Mesh details can be altered seamlessly as the modifiers remain uncompacted. Notably, no...

Then rotate the pen upwards and press the lever on the side - gravity will do the rest for you as the lead slides down into the pen.To store more leads just repeat step 2.Press down the lever on the side and you will be able to slide them in. You can...

1 Image of the whole set and another with the most significant measurements. All parts are oriented so that they do not need supports except for the complete parts. The complete bases can be printed as they are oriented without supports, depending...

Regardless, I often see people portray them as medium animals, more like Chocobo so I wanted to make my own models for our game.&nbsp;I based most of my details on the second edition art.&nbsp;Even though crodlu cannot carry as much as a normal mount...

Took the SVG into inkscape and exported it as a png and used that to make the STL in MatterControl (love the handy image to path and extrusion tools). all stl files will print flat and need to be heat formed in hot water. See <a...

I managed to strip the plastic out on my 1st test print because I was trying to tighten the clamp too hard.\r\n\r\nAt the moment, all I've done to verify that the parts are working is to print a small section of the extruder body and x-carriage and...

See the main image, in that filaments one and two have been unloaded by the MMU and the loops you can see are the maximum that gets pushed back on each. This solution is so much easier and quicker to load and unload than a flat panel filament buffer,...

... a file for thick smartphones or devices with a case. It is possible to use with a total thickness of up to 15-16 mm.Look at my new project - an ultra-thin bookmark for books and at the same time a phone standWatch a video about all three models:

Simply print the parts and assemble them together. Please refer to the images for assembly instructions. The case I printed at 0.2mm layer height and 0.15mm for all other parts. Refer to the file names to see if colour changes (CC) are required and...

... the best. A "thank you" to "phesketh01" for sharing their work. BTW-New to contributing to Thingiverse. It seems that some of the images will not show up in the preview window and I don't know how to fix this but all STL files are present. ...

Make sure to check out my tutorial linked above to easily add new pictures to the map.For those who like to use Tinkercad or don't feel like messing with the design much I have also added a 3x3 and a 4x4 puzzle without any image or map as .stl files...

Required hardwareThe Prusa Mini/Mini+ or General EU-3030 aluminium profile. Buy the Original Prusa Mini+: https://shop.prusa3d.com/cs/66-original-prusa-miniNo T-slot nuts or screws are needed as the design uses side tension to hold the...

It should be printed on its side as shown in the image below so that the sloping edge is smooth (printing at other orientations would cause the layer lines to cause too much friction on the arrow's nock when sliding in. UPDATE: Ive added some new...

All textures/images and associated files are included within the Blender file. The HDR lighting shown in the renders is not included (there are plenty of free ones available). The objects are named accordingly within the Outliner, with wheels on...

This is a case for a single audio microcassette (as used in dictation recorders and answering machines, not a "compact" cassette for music). Present features (compared to a standard commercially-made case): It snaps shut. It locks the tape reels in...

... to give a smooth finish so that there's no ridge when joining the top and bottom covers. How I Designed This =================== Fusion 360 and lots of little sample tests to get the recess for the switch just the right size! Category: Gadgets

But maybe instead of having snips around, we could just use a cupcake?Once printed and assembled, just slide in filament and snip!Ben of Materials1x Bright coloured filament (swap for boring colours if you prefer)2x M2x6mm hex bolts and nuts1x Single...

Else 0.2mm Infill: 25% Filament: Any Any Any Notes: STL At a Glance [click to open image in new window] Good for PLA. But highly recommended flexible material to play it safe.</p> <h6>#</h6> <p>Share the same filter cover cap and Valve Disc set of...

Using this system, it is easy to remove the caddy without tools.It features:3 storage compartmentsSide mounts for tools2 clips for Sharpies8 holes for Allen wrenchesSlots for SD cardsA large tray for small items such as nozzles or filament...

Read below for details.** **Note: Thingiverse is being very slow at rendering the STL preview images.*** There's a lot of space in the box and relatively few game components, so rather than use up a lot of filament as filler, this organizer also...